Wall Mounts for the Sony BRAVIA 3 II LED XR30M2 100-inch

Mounting specification

Its 600 × 400 mm pattern is a standard VESA size, so any mount listing that spacing within its supported range will bolt straight on. At 117 lb this is in the heavy-duty class. It needs a mount explicitly rated above that figure, fixings into solid framing or masonry, and realistically two people to lift it onto the bracket.

This is a conventional LED-backlit LCD panel, which at 117 lb is toward the lighter end for a 100-inch screen. That widens the field of compatible mounts, but it does not change the rule that the fixings go into framing.

Where the bolts land relative to your studs

At 23.6 inches across, this pattern spans past 16-inch studs and lands close to 24-inch centres, so it will reach solid framing on either spacing.

Specification sourced from the manufacturer listing and cross-checked against published panel data . Measure your own mounting holes before buying if you want certainty for your exact unit.

How high to mount it

Put the centre of the screen at seated eye level — about 42 inches from the floor for a normal sofa. On a 100-inch panel that puts the bottom edge at roughly 17 inches and the top at roughly 67 inches, or 5' 7" in feet and inches.

At this size the geometry starts to bite. A 100-inch screen centred at eye level has its bottom edge only 17 inches off the floor, which is below the top of most media consoles — so the console has to move, or the TV goes higher than ideal and you accept the compromise. Measure your furniture before you commit to the size. It also wants a viewing distance of roughly 11.2 feet for balanced viewing, so check that against where your seating actually is.

If a console or a mantel forces it higher, mount as low as the obstruction allows and use a tilting mount to angle the screen back toward you. The height calculator works out the exact number for your seating position, and the fireplace planner handles the above-the-mantel case including heat clearance.

If you need to tilt it

Mounting above eye level — over a fireplace, a dresser or a tall console — means the screen should angle down toward you. These tilt mounts are rated for the XR30M2's pattern and weight.

If it needs to swivel

Corner installations, open-plan rooms and kitchens usually want an articulating arm. Bear in mind that a full-motion mount applies far more leverage to the wall than a fixed plate does, so at 117 lb these want solid framing rather than anchors.

What else the job needs

The two things that stall a Sony install most often are hardware and cable length. Box hardware does not always include the right bolt for a specific panel, and the HDMI cable that reached the old stand rarely reaches once the TV is on the wall.

Other sizes of the XR30M2

The XR30M2 does not use one pattern across the range: your 100-inch is 600 × 400 mm, while the 43-inch is 200 × 200, the 50-inch is 300 × 300, the 55-inch is 300 × 300, the 65-inch is 300 × 300, the 85-inch is 400 × 400. A mount will not simply transfer between sizes in this range — check the specific size you own.

Other TVs with the same 600 × 400 pattern

These take the same mounts, which is useful if you are buying one bracket for a house with several TVs.

• Hisense ULED U8K U8K 100" — 157.2 lb
• LG QNED evo Mini-LED 85A QNED85A 100" — 145.3 lb
• Samsung Neo QLED 4K QN90D 98" — 135.4 lb
• Samsung Neo QLED 4K QN90F 98" — 135.4 lb
• Samsung Neo QLED 8K QN990F 98" — 149.9 lb
• Sony BRAVIA XR X90L X90L 98" — 148.1 lb

Frequently asked questions