Wall Mounts for the Sony BRAVIA 3 II LED XR30M2 50-inch

Mounting specification

Its 300 × 300 mm pattern is a standard VESA size, so any mount listing that spacing within its supported range will bolt straight on. At 24.6 lb the panel is light enough that almost any mount rated for its size will carry it comfortably — the VESA pattern, not the weight, is what limits your choice here.

This is a conventional LED-backlit LCD panel, which at 24.6 lb is toward the lighter end for a 50-inch screen. That widens the field of compatible mounts, but it does not change the rule that the fixings go into framing.

Where the bolts land relative to your studs

At only 11.8 inches across, this pattern is narrower than the 16 inches between studs — the TV's mounting holes sit between them. The mount's wall plate has to be wide enough to reach two studs, or you need a single-stud mount rated for the full panel weight.

In practice that means checking one spec people skip: the width of the mount's wall plate. A plate under about 16 inches wide can only reach one stud, and a single-stud mount carrying 24.6 lb wants to be explicitly rated for that. Mounts listed as fitting 16, 18 and 24-inch studs are the safe answer here, because they give you somewhere to land whatever your framing actually does.

Specification sourced from the manufacturer listing and cross-checked against published panel data . Measure your own mounting holes before buying if you want certainty for your exact unit.

How high to mount it

Put the centre of the screen at seated eye level — about 42 inches from the floor for a normal sofa. On a 50-inch panel that puts the bottom edge at roughly 30 inches and the top at roughly 54 inches, or 4' 6" in feet and inches.

A 50-inch panel leaves comfortable clearance above a normal console at this height, so the usual constraint is the wall itself rather than the furniture. It also wants a viewing distance of roughly 5.6 feet for balanced viewing, so check that against where your seating actually is.

If a console or a mantel forces it higher, mount as low as the obstruction allows and use a tilting mount to angle the screen back toward you. The height calculator works out the exact number for your seating position, and the fireplace planner handles the above-the-mantel case including heat clearance.

If you need to tilt it

Mounting above eye level — over a fireplace, a dresser or a tall console — means the screen should angle down toward you. These tilt mounts are rated for the XR30M2's pattern and weight.

If it needs to swivel

Corner installations, open-plan rooms and kitchens usually want an articulating arm. Bear in mind that a full-motion mount applies far more leverage to the wall than a fixed plate does, so at 24.6 lb these want solid framing rather than anchors.

What else the job needs

The two things that stall a Sony install most often are hardware and cable length. Box hardware does not always include the right bolt for a specific panel, and the HDMI cable that reached the old stand rarely reaches once the TV is on the wall.

Other sizes of the XR30M2

The XR30M2 does not use one pattern across the range: your 50-inch is 300 × 300 mm, while the 43-inch is 200 × 200, the 55-inch is 300 × 300, the 65-inch is 300 × 300, the 85-inch is 400 × 400, the 100-inch is 600 × 400. A mount will not simply transfer between sizes in this range — check the specific size you own.

Other TVs with the same 300 × 300 pattern

These take the same mounts, which is useful if you are buying one bracket for a house with several TVs.

• LG UHD UA75 UA7500 50" — 20.7 lb
• TCL Q6 Class Q651G 50" — 19.6 lb
• TCL S5 Class S551G 50" — 19.6 lb
• LG QNED 75 edge-lit QNED75 55" — 35.9 lb
• LG QNED 80 edge-lit QNED80 55" — 35.9 lb
• LG UHD UR8000 UR8000 55" — 30.9 lb

Frequently asked questions