Mounting a TV in a Chicago condo is a flat rate by screen size: $129 up to 54 inches, $159 for 55-69, $209 for 70-79, $299 for 80-94 and $399 for 95 and up, whatever floor you live on. What shapes the job is what the building put behind the paint. A tower partition is steel stud, a loft wall is brick, timber or concrete, and a vintage co-op wall is plaster over wood lath or solid masonry. Brick, stone, block and concrete add $99. Metal stud, plaster and drywall add nothing.
Two more things are particular to Chicago: the questions to put to your building before you book, and the city’s conduit rule for new outlets.
One city, three kinds of condo wall
| Building | Where | Behind the paint | What holds the TV |
|---|---|---|---|
| Tower | River North, West Loop, South Loop, Gold Coast, the lakefront | Drywall on metal stud, concrete at the structure | Toggles in steel, Tapcons in concrete |
| Loft conversion | River North’s gallery district, Fulton Market, Printers Row | Exposed common brick. Heavy timber in River North and the West Loop, concrete in Printers Row | Tapcons in brick and concrete, lag bolts in timber |
| Vintage co-op or courtyard building | Gold Coast, Uptown, Lakeview, Edgewater | Plaster-and-lath partitions, plaster over solid masonry | Lag bolts in studs, Tapcons in masonry |
The installer tests the exact wall you picked: a magnet pass, a knock, one small pilot hole behind where the TV will hang.
Towers: steel studs between rooms, concrete at the structure
The high-rise condos of River North, built from the 1990s on, are concrete and metal stud. So are the newer glass towers along Randolph Street in the West Loop, the Central Station towers in the South Loop, the 1960s International Style buildings in the Gold Coast and the lakefront high-rises of Uptown and Lakeview East.
The partition between rooms is light-gauge steel behind drywall. A lag bolt cuts a thread in it, then spins free. The right anchor is a SnapToggle, which goes through a 1/2-inch hole and turns a steel channel flat against the back of the stud. Four hold a fixed or tilt bracket. Six go under a full-motion arm, spread over two studs. Metal stud carries no surcharge, and our metal stud guide has the method.
Concrete is the frame: columns, shear walls, often the corridor wall. In the 1960s towers along Sheridan Road in Edgewater, many walls are poured concrete straight through. It takes a hammer drill, a 3/16-inch carbide bit and 1/4-inch Tapcons. Where drywall is furred off the concrete, the first hole measures the gap, so the Tapcon threads into concrete and not into air. Tower walls carry conduit and the odd sprinkler branch, so the wall is scanned before every hole. Concrete adds $99.
Loft buildings: brick, timber and concrete in plain sight
The loft conversions in River North’s gallery district, near the Merchandise Mart, and through Fulton Market in the West Loop were warehouses first: common brick walls, heavy timber posts and beams. Printers Row in the South Loop, the old printing houses north of Dearborn Station, is exposed common brick and concrete.
Brick takes a hammer drill and 1/4-inch Tapcons in the brick face or the mortar joint, whichever lines up with the mount holes. Old lime mortar is scraped with an awl before it is trusted. Painted brick chips, so every hole starts at low speed with the hammer action off.
A timber post is a different job two feet away: a 5/16-inch lag bolt in a pilot hole, after an awl probe for soft spots. Timber is wood, so the post stays at the base rate while the brick beside it adds $99.
Vintage co-ops and courtyard buildings: plaster over lath or masonry
The cooperative buildings on Lake Shore Drive in the Gold Coast date from the 1920s, and one apartment has two kinds of wall under the same paint. Walls that belong to the structure are plaster over solid masonry. Partitions between rooms are plaster-and-lath over wood studs. The courtyard buildings of Lakeview and Edgewater split the same way: exterior and party walls are common brick with plaster on thin furring strips, and only the partitions inside the unit are framed. Uptown’s six-flats and courtyard buildings are plaster-and-lath inside, common brick at the outer walls.
Plaster never carries a television by itself. A rare-earth magnet slid over the wall picks up the lath nails as a vertical line, which marks a stud. No line and a dead, solid knock point to masonry, and a 1/8-inch pilot hole confirms it. Studs get 5/16-inch lag bolts, two per stud, the last turns by hand so the plaster does not crack. Masonry gets Tapcons long enough to pass the plaster and thread an inch or more into the brick. Nothing hangs on a furring strip, and no bracket is tightened against plaster that sounds drummy and gives under the palm.
A partition is the base rate and a masonry wall adds $99, so when both suit the room, you choose after the test.
What to ask your building before you book
Every tower, loft building and co-op sets its own rules for outside installers, and only its management office or board can tell you what they are. Ask five things:
- People. Does the door staff or the office need the installer’s name ahead of the visit?
- Noise. On which days and hours is drilling allowed?
- The box. Does a large TV have to come up by service or freight elevator, and does it need a reservation? An 85-inch box does not fit in a passenger elevator.
- The wall. Does the board want to approve a mount first, and is any wall, such as one shared with a neighbor, off limits?
- Cables. May low-voltage cable run inside a wall, or must everything stay on the surface?
Tell us the building’s name and its answers when you book, and the appointment is set around them. None of it moves the flat rate. Renting from an owner? Get the owner’s yes in writing, since a mount leaves four to six holes to fill at move-out.
The Chicago conduit rule: who runs power, where the cables go
The City of Chicago Electrical Code requires wiring to run in metal conduit. NM cable, the flexible kind used in most of the country, is not allowed inside the city, and every neighborhood in this guide is inside it.
So a new outlet behind the screen is an electrician’s job, run in EMT, and not part of a mounting visit. If you want one, book the electrician first and tell us where the box will sit.
The installer’s concealment is low-voltage only: HDMI, optical, network and speaker cable. In-wall concealment is $99 per TV and needs a hollow wall, meaning a metal stud partition in a tower or a plaster-and-lath partition in a vintage building. A magnet checks the bay first, so the opening misses any conduit.
Brick, concrete and plaster over masonry have no cavity. There the cables ride a paintable surface raceway at $79 per TV, and the power cord shares it to the nearest outlet. The raceway is also the answer when a building wants nothing opened.
What a Chicago condo install costs
- Labor by screen size: $129 (up to 54”), $159 (55-69”), $209 (70-79”), $299 (80-94”), $399 (95” and up, two technicians)
- Brick, stone, block or concrete: +$99
- Metal stud, plaster, drywall, a timber post: no surcharge
- In-wall cable concealment: $99 per TV
- Paintable surface raceway: $79 per TV
- Bracket: your own, or ours at $49 flat up to 54 inches and $69 above, $59 or $79 for full-motion
- Soundbar mounting: $79
- Travel fee: none
A 65-inch TV on a River North metal stud partition with the cables inside the wall is $159 plus $99, so $258 before the bracket. A 75-inch TV on Printers Row loft brick is $209 plus the masonry surcharge, so $308.
The Chicago cost page works through more cases, the price list has the full card, and the price estimator gives a number for your own screen and wall.
Express Mounting has no Chicago office. It dispatches an installer from its vetted Chicago network, and the areas covered are on the Chicago TV mounting page. Book before noon for same-day service, with arrival within 2-4 hours of confirming. Call (470) 777-4077, 8 AM to 8 PM every day, or request a time online.
Frequently asked questions
How much does it cost to mount a TV in a Chicago condo or high-rise?
A flat rate by screen size: $129 up to 54 inches, $159 for 55-69, $209 for 70-79, $299 for 80-94 and $399 for 95 and up. Brick, stone, block or concrete adds $99. The bracket is a separate line.
Can a metal stud wall in a Chicago high-rise hold a 75-inch TV?
Yes, with the right hardware. Lag bolts strip thin steel studs, so the installer uses SnapToggles that clamp behind the stud: four for a fixed or tilt bracket, six for a full-motion arm, spread across two studs.
Can you add an outlet behind the TV in my Chicago condo?
No. The City of Chicago Electrical Code requires wiring in metal conduit, so a new outlet is an electrician’s job anywhere inside the city. Our concealment is low-voltage only: HDMI, optical, network and speaker cable, at $99 per TV inside a hollow wall.
Does my condo or co-op board have to approve a TV mount?
Only your building can answer that. Ask the management office or the board about approval, drilling hours, a service elevator for the box, and cable inside the wall, then tell us when you book. The price does not change.
Can you hide TV cables on a brick or concrete wall?
Not inside it, because solid brick and concrete have no cavity. The cables ride a paintable raceway on the surface, at $79 per TV, and the power cord shares it to the nearest outlet.