Skip to content
Same-Day Service · Free Estimates Text a photo

Field guide · Installation Tips

Fireplace TV Mounting in Dallas-Fort Worth: Brick, Cast Stone and Stone Veneer

Mounting a TV over a DFW fireplace: anchors for brick, cast stone and stone veneer, the +$99 masonry rate, mantel height, heat and cables. From $129.

By Alex Crabinsky 10 min read

Fireplace TV Mounting in Dallas-Fort Worth: Brick, Cast Stone and Stone Veneer

Mounting a TV over a fireplace in Dallas-Fort Worth costs the flat rate for the screen, $129 to $399 by size, plus $99 when the bracket goes onto a brick, cast stone or stone face. In a DFW house the fireplace is usually the one interior wall where masonry comes in, and which of those three faces you have decides the anchors. Brick and cast stone hold the bolts themselves. Thin stone veneer holds nothing, so the bolts have to reach the wood studs behind it.

Nearly every DFW house is brick veneer over wood studs with drywall inside, and the brick outside never comes into play on an interior wall. The fireplace is the exception. It brings three more questions with it: how high the mantel pushes the screen, how hot the face gets, and where the cables go.



Which face is on your fireplace

FaceWhere it turns up in DFWWhat carries the TV
Brick1980s ranch dens in Allen and East Plano, Addison townhomes, 1990s Keller houses1/4-inch Tapcon anchors in the brick
Cast stone1990s and 2000s two-stories in Plano, Allen, Frisco, Colleyville and SouthlakeTapcons through a carbide pilot, 3 inches off any corner
Stone veneer2010s builds in Frisco, Keller, Southlake and Colleyville4-inch lag bolts through the stone into the wood studs

All three carry the same +$99 masonry surcharge. What differs is where the load ends up.

The region sits on expansive Blackland Prairie clay, so where masonry meets drywall at a fireplace corner, the two move separately. The mount commits to one material, and no anchor goes into a cracked or patched section.


Brick: anchors in the face or the joint

The 1980s ranches of Allen and the 1970s and 80s ranches of East Plano have a den fireplace that is full-height brick to the ceiling. The 1980s townhomes of Addison, the 1990s houses of Keller and the Ross Downs streets of Colleyville lean brick too.

Brick holds the TV directly. The installer drills with a carbide bit at low speed and sets 1/4-inch Tapcon anchors in the brick face or the mortar joint, whichever lines up with the mount holes. The brick carries the surcharge. The drywall beside it does not.


Cast stone: hard in the middle, brittle at the edges

Cast stone is the surround of the 1990s and 2000s two-story: Willow Bend and Kings Ridge in Plano, Bethany Lakes in Allen, the older Stonebriar streets of Frisco. In Southlake, estate builds from the late 1990s on ran it from hearth to ceiling.

It drills like hard concrete under a carbide bit and chips at the edges. So the bracket is laid out on the stone first, and every anchor stays 3 inches in from the corner of a block. Quarter-inch Tapcons carry the mount.


Stone veneer: the stone holds nothing

Phillips Creek Ranch and Newman Village in Frisco favor a floor-to-ceiling stone fireplace, as do Marshall Ridge in Keller and the newer builds of Southlake and Colleyville. Most of that stone is thin veneer: 1 to 1.5 inches of ledgestone or manufactured stone on a scratch coat over cement board, with wood studs behind. A short masonry anchor bites the stone and the scratch coat and stops, which is not what you want holding 70 pounds of glass over a firebox.

So the stone carries none of the load. The installer finds the studs, drills through the veneer with a carbide bit at low speed so it does not crack, and drives 1/4-inch by 4-inch lag bolts into the framing. The +$99 still applies, because carbide drilling through stone replaces the usual stud work.


How high is too high over a mantel

On a plain wall the middle of the screen belongs near seated eye level, about 42 inches off the floor on most couches. A mantel rules that out, so the working rule is a limit: keep the upward viewing angle from the seat at or under about 15 degrees. Measured to the middle of the screen:

Seat to screen15 degrees above eye levelHighest screen center, eye at 42 inches
8 feetabout 26 inchesabout 68 inches
10 feetabout 32 inchesabout 74 inches
12 feetabout 39 inchesabout 81 inches

DFW houses test that limit. In a Starwood or Stonebriar two-story in Frisco, the builder’s pre-wire plate often sits 70 inches up, which puts the center of a 65-inch panel near 80 inches. In Keller, a 60-inch mantel puts a fixed TV too high for a couch 10 feet back. In Timarron and Shady Oaks in Southlake, the surround climbs a two-story family room.

A tilt bracket turns the picture toward you but does not lower the screen. Past 15 degrees the choices are a lower spot, another wall, or a pull-down mount, which parks the screen above the mantel and drops it to eye level for viewing. Installing your own pull-down mount is $99 on top of the labor rate. Our TV height chart and calculator does the arithmetic by screen size.


The heat check

Most of these fireplaces are gas. The gas logs run for 20 minutes, then an infrared thermometer reads the face where the screen would sit. Behind a proper mantel the surface usually holds between 90 and 105 degrees. A cast stone face with no mantel can pass 120.

Under about 100 degrees, a tilt mount at the lowest workable height is fine. Hotter than that, the installer moves to a pull-down mount that parks the screen high and brings it down for viewing, or to another wall. Our guide to mounting a TV over a fireplace covers the general case.


Where the cables go

Nobody cuts a cable path through brick or stone. Where there is a framed chase beside the firebox, the cables run down inside it, and that is in-wall concealment at $99 per TV. It uses in-wall-rated cable and an in-wall power kit, so no cord that plugs into an outlet is buried. The chase often carries the return-air duct too, so a probe hole comes first.

Where there is no chase, a raceway matched to the surround color carries the cables down the face. A paintable raceway is $79 per TV.

When the receiver lives in a closet down the hall, the run crosses the attic. Texas attics run well above 130 degrees in summer, so that run gets the first slot of the morning, CL3 cable and fiber-optic HDMI past 25 feet.


What a DFW fireplace install costs

  • Labor by screen size: $129 (up to 54”), $159 (55-69”), $209 (70-79”), $299 (80-94”), $399 (95” and up)
  • Brick, cast stone or stone face: +$99. Drywall above a mantel is a stud job with no surcharge.
  • Your own pull-down mount (MantelMount type): $99 to install
  • In-wall cable concealment: $99 per TV
  • Paintable raceway: $79 per TV
  • Bracket: your own, or ours at $49 flat up to 54 inches and $69 above, $59 or $79 for full-motion
  • Soundbar mounting: $79
  • Travel fee: none

Three sums, each before the bracket. A 65-inch TV on a brick fireplace is $159 plus $99, so $258. On your own pull-down mount it is $357. With the cables down the chase as well, $456.

The Dallas cost page works through more cases, the price list has the full card, and the price estimator gives a number for your own screen and wall. If you rent, ask the owner or management in writing whether the surround may be drilled, since a clause that allows a drywall mount does not always cover masonry.

Express Mounting has no Dallas office. It dispatches an installer from its vetted DFW network, and the cities covered are on the Dallas-Fort Worth TV mounting page. Book before noon for same-day service, with arrival within 2-4 hours of confirming. Call (470) 777-4077, 8 AM to 8 PM every day, or request a time online.


Frequently asked questions

How much does it cost to mount a TV over a fireplace in Dallas-Fort Worth?

The flat rate for the screen size plus the masonry surcharge: $129 up to 54 inches, $159 for 55-69, $209 for 70-79, $299 for 80-94 and $399 for 95 and up, with +$99 for a brick, cast stone or stone face. A 65-inch TV on brick is $258 before the bracket.

Does the masonry surcharge apply to a stone veneer fireplace?

Yes. Thin stone veneer is cosmetic, so the installer drills through it with a carbide bit and drives 4-inch lag bolts into the wood studs behind. Drilling through stone replaces the usual stud work, so the +$99 applies as it does on brick and cast stone.

How high is too high for a TV over a mantel?

Keep the upward viewing angle from your seat at or under about 15 degrees. From a couch 10 feet back, that puts the middle of the screen roughly 74 inches off the floor at most. Past that, a lower spot or a pull-down mount works better.

Is the wall above a gas fireplace too hot for a TV?

The installer measures. The gas logs run for 20 minutes and an infrared thermometer reads the face where the screen would sit. Under about 100 degrees a tilt mount is fine. A cast stone face with no mantel can pass 120, which calls for a pull-down mount or another wall.

Where do the cables go on a brick or stone fireplace?

Not through the masonry. Where there is a framed chase beside the firebox, the cables run down inside it. Where there is none, a raceway matched to the surround color carries them down the face.


Rather have it done than do it? TV mounting across Dallas-Fort Worth: flat rates from $129, same-day when booked before noon.

Share

We install what we write about.

TV mounting from $129 - same-day slots in 15 US metros, wires hidden, gear set up before we leave.

Express Mounting hangs TVs in 15 US metros and 561 cities at one flat price list, from $129 per TV, same day when you book before noon. Pick your metro for who installs there, the price list and every city we cover.

Price your install in a minute

Find Your TV's Mount Get a Pro Quote

Text a photo of your wall

Point your phone's camera here to start a text to +14707774077. Add a photo of the wall and your TV's size, and we reply with your price and the first open time.

QR code that starts a text message to +14707774077
Use the quote form instead